Nationallay AIM Compliant
Under 200 G/L
Crosslinked Oxidative System
Clear wood coating/varnish
Excludes SCAQMD
Rymar Xtreme Weather Wood Coating is a high-solids oil base coating that gives wood a rich, beautiful semi-transparent look. It is a wet on wet coating that will last for years.
SUNSEAL SUNSCREEN We incorporate special ultra violet absorbers to help retard premature graying of wood along with ultra violet stabilizers, we use special pigments and other proprietary additives to help block out any other ultra violet light thay may penetrate through to the surface.
CITRONELLA OIL Citronella oil is a naturally occurring organic substance obtained from leaves of Asiatic lemon oil grass. Commonly used as a natural mosquito repellent, Rymar Wood Coating with citronella oil may help keep those pesky insects away when properly applied to your project.
CHEW STOP is a natural pepper additive, that may help prevent animals from chewing on wood. Helps discourage bothersome bees, bugs, spiders and birds which might otherwise cause damage to your wood.
NATURAL & SYNTHETIC OILS A blend of Supreme linseed oil and synthetic oils allows for good penetration of the wood and still gives a surface build for greater protection of the substrate.
PTFE is used to both repel water and help protect against weather erosion.
WATER REPELLENT Other so-called water repellent wood coatings can't match the water beading qualities of our coating. Along with the oils and PTFE, you get superior water protection. While most others last for a very short time, ours beads like nothing you've seen before. In order to help stabilize wood, you must keep out moisture.
XTREME WEATHER WOOD COATING has 25% more solids than our Premium Coating.
ADVANTAGES
RYMAR WOOD COATING is Nationally AIM compliant less than 350 G/L.
RYMAR WOOD COATING has up to 55% solids.
RYMAR WOOD COATING and grouped Nano Technology, form a protective shield unachievable prior to this technology.
RYMAR WOOD COATING with Nanofine Oxide Sun Seal, an advanced form of sunscreen, gives unsurpassed UV protection.
RYMAR WOOD COATING contains citronella, a natural mosquito repellent.
RYMAR WOOD COATING has special waterproofing agents to prevent moisture penetration which helps stop checking, cracking and warping.
RYMAR WOOD COATING is not a preservative, therefore when properly applied it is a safer alternative.
RYMAR WOOD COATING has both natural and synthetic oils.
RYMAR WOOD COATING incorporates PTFE to help prevent surface erosion.
RYMAR WOOD COATING is formulated to be grease resistant, a must where food and beverages are prepared and served.
RYMAR WOOD COATING naturals have special pigments that remain virtually invisible when applied, for a clean natural look.
RYMAR WOOD COATING is available in clean and semi-transparents.
DIRECTIONS
Wood should be clean and dry. It is recommended that Rymar Rinseable Soap be used to clean the wood before sealing. If using bleach do not allow it to remain on the wood longer than five minutes. Between coats clean with Rymar Rinseable Soap and water, no bleach. Do Not Use Metal Pails. Do Not Use Hard Water. Ask your dealer about preparing surfaces for coatings; they may be able to advise you otherwise depending on your situation. A coat should be applied about 30 days after completion of project, provided wood is clean and dry. Do a wet on wet or wet on tack coat: seal two or three boards from one end to the other or up to a natural break, go back and do them again. Do Not Allow Coating To Puddle. On very dry wood you may need to repeat the procedure in six months to a year. In some cases you may need to reseal or maintain your project more often. Clear will not prevent graying as well as the pigmented colors. When doing wood siding, dipping is best to get all sides. When installing wood siding, saw cuts must also be sealed. End grain on all wood should always be sealed. Coating may be applied with a bristle brush, spray gun, or by dipping. Be sure to shake well before using and stir thoroughly before and during use. If you have multiple batch numbers, mix them together before applying.
Note! Do a test: Try a brushout on your project to ensure the color and product is what you want before doing your entire project.
XTREME WARRANTY
Rymar warrants that the contents of this can are not defective. In the event this product fails to comply with the warranty it is Rymar LLC's option to furnish replacement of product or a refund of the purchase price with proof of purchase. In the event of product failure and or misuse of this product, Rymar and its affiliates assume no responsibility (implied or otherwise), for labor, substrate, other items or materials used in either the application of this product or otherwise.
PRODUCT SPECIFICATIONS
Restrictions: Apply when air and surface temperature are above 50 degrees and below 85 degrees.
Weight Per Gallon: 7.70
Solids by Weight: 54.48
VOC: Less than 350 G/L
Paintable: No
Flashpoint: 105 degrees
Type: Clear Wood Coating/Varnish
Vehicle: Solvent
Finish: Flat
Colors: 11
Containers: 1 Gallons, 5 Gallons
Coverage: Approximately 200-400 sq ft per gallon, depending on porosity of wood.
Drying Time: Approximately 24 to 48 hours depending on temperature, 30 days to full cure. All times are temperature and moisture dependent.
Clean Up: Mineral Spirits
Application: Bristle Brush, sprayer
Reduction: None
Cure: Air Dry
Substrate: Wood
CLEAR WILL NOT STOP GRAYING AS LONG AS THE PIGMENTED COLORS
